MOTORLINE MX4SP DSM
HR KIT LIBERTY 220V
Reference : :
|Number of buttons||4|
|Type of programming||Programming with the receiver|
|Type of battery||12V(27A)|
|Dimensions||7 x 3 x 2 cm|
|Battery and instructions included||Yes|
|This remote replaces||SMD 26.995 MHZ OLD, GIBIDI 26.995-2, GIBIDI 26.995-4 OLD, BOSCH 27.145 MHZ, SERVO-LIFT 27.195, SERVO-LIFT 40.685, WECLA 40.685 MHZ 1K, WECLA 40.685 MHZ 2K OLD, DEA 433-1, DEA 433-2, ALLDUCKS 6203 12 BIT, DUCATI 6203 GREY, DUCATI 6203 RED, WECLA 801016F, WECLA 801023F-27MHZ, WECLA 801023F-40MHZ, WECLA 806011, WECLA 807117D , WECLA 807117F, WECLA 807117F TX1, WECLA 807117F TX2, WECLA 808114, CARDALE AZAR 2058 QUANTEK, BERNAL B 260.254-N|
MOTORLINE MX4SP DSM remote control available only in one colour which is black. This remote control is replaced by and fully compatible with the new model MOTORLINE FALK RCM which has 4 buttons and is at the same price. The Motorline with the reference MX4SP DSM is a 4-button remote control gate opener, using the frequency 433.92 MHz.
To improve your daily comfort when using your motorized gate, MX4SP DSM remote control is the best option. By investing on this type of transmitter, you are choosing a convenient and reliable gadget.
A Rolling-code remote control which programming is done with the receiver, the gate opener has four buttons and is easily used by its convenient shape.
For more information on this gate fob, consider looking through the manual (PDF) or you can check out the video below which explains in detail all the the main steps to assist you in programming your MOTORLINE MX4SP DSM gate remote control.
WARNING: The LED of this remote control twinkles. Do not confuse this transmitter with the one of the same appearance which LED flashes. If the LED flashes, then it’s the Motorline MX4SP RCM model, not compatible with the model displayed here.
ATTENTION: There are two different models, you should see on the circuit of your key fob if there’s any resistor at the lower right of the circuit, if there is then it’s the model: MOTORLINE MX4SP DSM.
If there are no resistors, then it’s the model MOTORLINE MX4SP RCM.
Note: Transmitters with different frequencies are not compatible.
The remote control’s operation
MOTORLINE MX4SP DSM remote control operates with a frequency of 433.92 MHz to emit signals to the receiver and is powered with a battery 12V, excellent voltage to optimize the good autonomy of the device.
The programming is quick and simple because it’s done with the receiver.
MOTORLINE MX4SP DSM remote control replaces the following Motorline gate remotes:
MOTORLINE MXS4SP RCM
It is compatible with the following Motorline gate remotes:
NOTE: A remote control with the inscription RCA on the back is compatible with the model shown here.
MX4SP DSM a 4-channel transmitter that controls all the movements of your gate, rolling shutters, lighting, garage door...etc according to your specifications. The frequency of this item is 433.92 MHz.
As for its programming, the device has a very high security coding system (Rolling Code), you have to program your remote in your receiver.
MX4SP DSM remote control with 4 buttons for garage door operators and automatic gates. This model is powered by a 12V battery type 27A. A 4-channel Rolling code hand transmitter with 0 code switch and a transmission distance of 100m in open space, well-functioning !
The registration of the MX4SP DSM keyfob only takes few minutes and the programming requires no special equipments.
If you have difficulties in programming the remote, don’t worry, a manual is delivered with the remote control.
Good to know
Choose a remote control that operates under the same frequency as your original model to guarantee the compatibility of the two items. Otherwise, your remote won’t function on your automatism. The coding system of your new device also must be identical to the one of your original remote control to successfully control your motorized gate.
It is important to know that there are three types of programming (coding systems) : Switches, auto-programming, and programming in the receiver.
To choose the correct remote control, it is highly recommended to consider the following criteria : the brand, the frequency, don’t neglect neither the number and the colour of the remote control buttons. These elements are usually used by the manufacturers to identify their products.
MX4SP DSM remote control is only 69 mm long, a width of 33 mm and a thickness of 13 mm. If you are looking for a good design remote control and easy to use, choose right away the MX4SP DSM. This model is highly aesthetical, its special shape and reduced size makes it very easy to handle, it can be used as a keyring or keyfob,with the support included in the pack. It is also shock-resistant device which makes it very tough and strong under all kind of pressure or shocks.
Please note: If you keep the programming button of your receiver pressed down too long, you will erase all the programming code of all your remote controls that have already been programmed.
Programming of your new remote control:
Open the casing of your receiver located next to your motor.
On the receiver circuit board, press the programming button and let it go (ENR, MEMO, PROG, REC…) according to the model. The LED on the receiver illuminates.
Press a button on your new remote control for 1 seconds and let it go. The LED on the receiver turns off immediately or in the following 10 seconds.
Your new remote control is programmed.
Finding it hard to program your MOTORLINE MX4SP DSM gate remote control ?
No worries, we are available to help using our expertise. Firstly, consider reading the notice sent with each MX4SP DSM remote control. our website also provides tutorials for most MOTORLINE remote controls. If you need any more help, call our free helpline. One of our experts will take you through each step to help you program your gate remote control. You can even send us a photo using your mobile to +33 (0)616 962 454. This number is exclusively reserved for receiving MMS photos.
Founded in 1986 by the current administrator André Viana, André Group has more than 30 years of experience.
During the first 24 years of existence, the Group was made up of a series of companies from several areas related to mechanics and technology. It was a very enriching time, due to the diversity of branches involved, which provided a vast experience with leading automation countries, such as Germany and Italy, through contact with the most diverse international and national markets.
In 2010 all the companies were acquired and merged into one by the current administrator and founder, thus giving rise to Electrocelos S.A.
Since that time, a new direction has been traced, creating a strategy that focuses on the quality of products and service, always keeping in mind customer satisfaction, leading Motorline Professional brand to cross borders and become a reference brand automation market.
Today, Motorline Professional is represented in more than 50 countries through distributors and professionals in the industry who put their trust and confidence in the brand and the company. They are more than 15 thousand between resellers and installers that are officially specialized in the installation of our products, in order to comply with the safety and quality standards required by Motorline. There are also teams working exclusively in specific countries, making the export in the company’s largest market.
Why buy your MOTORLINE MX4SP DSM remote control on our website?
-Advantage 1 :
Hoping to take delivery of as soon as possible? Choose 24-hour delivery anywhere in United Kingdom.
-Advantage 2 :
Purchase multiple remote controls and save money by taking advantage of our shipping offers.
-Advantage 3 :
Hoping to save time and be able to use your MOTORLINE MX4SP DSM gate remote control right now? You’ll be glad to know that all our remote controls come with batteries. This means you can quickly start using your MOTORLINE MX4SP DSM remote control.
Remote Control Express will lead you through each stage of the process of buying your MOTORLINE MX4SP DSM remote control.